Skip to content
Frequency Generator

How to Find the Frequency of a Sound You Can Hear

Something in the room is making a noise. A fridge hums, a charger whines, a monitor sings faintly when the screen is dark. You want to know what frequency it is, to track down the source, to describe it to someone, or just because it is driving you up the wall.

You can find the frequency of a sound with a tone generator and your ears, usually to within a few hertz. The method is simple. The one mistake almost everyone makes is getting the answer an octave wrong, and that is easy to check once you know to look for it.

Try Frequency Generator

Tone generation, sound tests, and musical tuning in one app.

First: is it a tone, and is it in the room?

Matching works for sounds with a clear pitch: a hum, a whine, a whistle, a ring. If you could hum along with it, you can match it. It works poorly for hiss, rumble or rattle, which spread their energy across many frequencies at once.

Next, check that the sound is actually out in the room. Move around, put your hand over one ear, step outside. A sound from a device gets louder or quieter as you move and changes when you block your ears. If you hear a ringing, buzzing or hissing that stays the same wherever you go and nobody else hears it, talk to a doctor or audiologist rather than hunting for it with a tone generator.

One caution about “nobody else hears it”: younger people can hear high whines that many adults cannot, so a teenager hearing a charger that their parents cannot is often just a difference in hearing range by age.

Matching by ear: the bracket method

You need a tone generator you can adjust in small steps. Frequency Generator accepts decimal frequencies, which helps once you are within a few hertz.

  1. Turn the volume down first. Start the tone quieter than the sound you are matching. You are comparing pitch, not loudness, and a louder tone simply drowns out the source.
  2. Get a rough range. Try 200 Hz, 1 kHz and 5 kHz and decide which is closest. If you can hum the sound, that alone tells you it is probably below about 1 kHz.
  3. Bracket it. Pick one tone that is clearly too low and one that is clearly too high. Try the frequency halfway between. If that is still too low, it becomes your new lower bound; if too high, your new upper bound. Keep halving the gap.
  4. Finish with beats. When you are within a few hertz, play the tone while the sound is going. Two close frequencies produce a slow pulsing in loudness, called beating, at a rate equal to their difference. Two pulses per second means you are 2 Hz off. Adjust until the pulsing slows to nothing.
  5. Write the number down, then check octaves. See the next section.

Beats only work if the source is steady and both sounds reach you at a similar level. For a sound that wavers, settle for the closest match you can hold.

The octave trap

The most common mistake is not being a few hertz off. It is being off by a factor of two. Tones an octave apart share a note name and blend so well that the ear easily mistakes one for the other. A 120 Hz hum and a 240 Hz tone can feel like a match even though one is double the other.

To check, play half and double your answer. If 120 Hz seemed right, try 60 Hz and 240 Hz. The true match merges into the source as one sound. An octave neighbor sounds right but sits slightly apart, thinner or as a separate layer.

Real sounds also contain harmonics, quieter tones at whole-number multiples of the lowest one. You may have matched the second or third harmonic instead of the fundamental. This is especially common with low hums: your ears are much less sensitive at 50 Hz than at 150 Hz, so the harmonic can be the part you notice most.

Common culprits and their frequencies

Source Typical frequency Nearest note
Mains hum, 50 Hz countries 50 Hz G1, slightly sharp
Mains hum, 60 Hz countries 60 Hz Between B♭1 and B1
Transformer buzz, 50 Hz mains 100 Hz G2, slightly sharp
Transformer buzz, 60 Hz mains 120 Hz Between B♭2 and B2
Old CRT television whine About 15.6–15.7 kHz Too high to matter
Coil whine A few kHz and up, varies Varies

Mains hum. Electricity is delivered at 50 Hz in Europe, Africa, Australia and much of Asia, and at 60 Hz in North America and some other countries. Japan uses both: 50 Hz in the east and 60 Hz in the west. Audio gear with a grounding problem hums at the mains frequency and its harmonics.

Transformer buzz. Transformers and many power supplies buzz at twice the mains frequency, 100 Hz or 120 Hz, because the magnetic core flexes once on each half of the electrical cycle.

Coil whine. Graphics cards, laptops, chargers and LED drivers can whine when small components vibrate under changing load. The pitch usually sits somewhere from a few kilohertz up toward the top of hearing, and it often changes with what the device is doing, such as the frame rate in a game.

The old TV whine. If you remember a high whine from tube televisions, that was the line scanning circuit: about 15.7 kHz on NTSC sets and 15.6 kHz on PAL sets.

Using a spectrum analyzer instead

If matching by ear is frustrating, a spectrum analyzer app shows sound as a graph of level against frequency, and a steady tone appears as a sharp peak. A few things to know before you trust it:

  • Phone microphones have limits. They are fine across most of the audible range but less reliable for deep hums and the highest whines.
  • Resolution depends on settings. A larger FFT size gives finer frequency resolution but reacts more slowly. If the peaks look wide, increase it.
  • The tallest peak is not always the pitch you hear. For a hum, the strongest peak is often a harmonic. Look for the lowest peak in an evenly spaced series.

The most reliable workflow uses both: find the peak on the analyzer, then confirm it by ear with a tone at that frequency. If the tone blends into the sound, you have it.

Turning a frequency into a note name

To name the note, work out how many semitones it sits from A4: 12 × log2(frequency ÷ 440). Round to the nearest whole number to get the note, and the leftover times 100 gives the cents. For example, 1,000 Hz is 14.21 semitones above A4, which makes it B5, 21 cents sharp.

Or skip the arithmetic. The note frequency chart lists every note, and the online tone generator shows the nearest note as you adjust the frequency. For whines above 8 kHz, the high-frequency sound generator covers 8 to 22 kHz.

Frequency Generator puts the same thing on your phone, with decimal precision from 1 Hz to 22,000 Hz, which makes it practical to carry right up to the source of a noise. Its multi-oscillator can hold several candidate tones at once, so you can compare an answer against its octaves without retyping anything.

Matching takes a while, so protect your ears and your speakers along the way. Start every tone at a low volume. High tones are perceived as quieter than they really are, which makes it easy to turn a 12 kHz tone up to a genuinely loud level without noticing. Sustained low tones at high volume can damage small speakers, and a loud sweep through headphones is never a good idea.

Get occasional updates

New features, tips, and the occasional announcement. No spam.

More from us